Aircraft Materials and Analysis

Tariq Siddiqui is a manager of aircraft maintenance at a commercial airline and a professor at Embry Riddle Aeronautical University. He has more than 20 years of experience in aviation maintenance, management, project management, environmental regulations, and incident and accident investigation.

Introduction
Chapter 1. Aircraft Design
Military Standard—(Mil-Std-1530C) Aircraft Structural Integrity Program
Military Standard—(Mil-Std-882E) Standard Practice for System Safety
Military Standard—(Mil-Std-8861B) Airplane Strength and Rigidity Flight Loads
Military Standard—(MIL-A-8870C) Airplane Strength and Rigidity, Vibration, Flutter, and Divergence
Review Problems
Endnotes
Chapter 2. Aircraft Material
Properties of Materials
Materials Used in Aircraft Construction
Nonmetallic Aircraft Materials
Materials of Aircraft Hardware
Materials—Aircraft Lubricants
Review Problems
Endnotes
Chapter 3. Loads on the Aircraft
Aircraft Loads
Flight Loads
Moment, Moment Arm, and Torque
The Vector and Vector Components
Lift Pressure and Wing Loading
Centripetal and Centrifugal Forces
Landing Loads
Ground Loads
Fuel Tank Loads during Emergency Landing
Maneuvering Loads
Aerodynamic Heating
Review Problems
Endnotes
Chapter 4. Stress Analysis
Strain and Stress-Strain Relations
Stress Transformation
Stress Concentration
Fatigue-Stress Concentration
Behavior of Materials under Stress
Factors Affecting Elastic Properties
Modulus of Elasticity
Elasticity; Proportionality of Stress and Strain
Summary Definitions
Review Problems
Endnotes
Chapter 5. Torsion, Compression, and Bending Loads
Torsion
Shaft Failures
Shear Flow in Torsion
Compression
Compressive Strength and Failures
Calculation of Stress
Elastic Stability—General Condition
Curved Beams
Nonuniform Loading of Circular Plates
Flat-Plate Ultimate Strength
Review Problems
Endnotes
Chapter 6. Aircraft Structure Riveted Joints and Pressure Vessels
Riveted Joints
Examples of Lap Joints
Modes of Failure in Riveted Joints
Design and Limitations
Eccentric Loading of Riveted Joints
Stress Analysis of Riveted Joints
Riveted Joints—Common Terms
Pressure Vessels and Pressure Lines
Pressure Vessels
Aircraft Pressure Lines
Difference between Pneumatic and Hydraulic Systems
Review Problems
Endnotes
Chapter 7. Heat Treatment of Aircraft Metals
Metalworking Processes
Ferrous Metals
Heat Treatment Process
Time, Temperature, and Transformation
Continuous Cooling Transformation
Difference between TTT and CCT
Nonferrous Metals
Aluminum and Aluminum Alloys
Wrought Aluminum
Magnesium and Magnesium Alloys
Titanium and Titanium Alloys
Copper and Copper Alloys
Monel and K-Monel Alloys
Substitution of Aircraft Metals
Cold-Working and Hardening
Extruding
Quenching Media
Review Problems
Endnotes
Chapter 8. Aircraft Fatigue and Aircraft Material Fatigue
Fatigue in Material
Fatigue Testing (S-N Curve)
Fatigue and Crack Growth
Military Standard—(Mil-A-83444) Airplane Damage Tolerance Requirements
Stress-Corrosion Cracking
Control of Stress-Corrosion Cracking
Limit of Validity (LOV)
Review Problems
Endnotes
Chapter 9. Aircraft Corrosion
Why Metals Corrode
Types of Corrosion
Forms of Corrosion
Stress Corrosion
Exfoliation
Hydrogen Embrittlement
Corrosion of Metals
Corrosion of Ferrous Metals
Factors Affecting Corrosion
Corrosion-Prone Areas in Aircraft
Factors in Corrosion Control
Corrosion Inspection and Detection
Preventive Maintenance of Corrosion
Review Problems
Endnotes
Chapter 10. Dynamic Stress, Temperature Stress, and Experimental Methods
General Conditions
Remarks on Stress due to Impact
Temperature Stresses
Experimental Methods
Stress Pattern Analysis by Thermal Emission
Review Problems
Endnotes
Chapter 11. Composites
Applications of Composites on Aircraft
Fiber-Reinforced Materials
Laminar or Laminated Composites
Particulate-Reinforced Composites
Mechanics of Composite Material
Stress and Strain in a Laminate
Composite Fatigue and Damage Tolerance
Aircraft Accident–Crashworthiness
Composite Material
Composite Manufacturing and In-Service Defects and Damages
Composite Maintenance and Inspection
Composite Safety
Review Problems
Endnotes
Chapter 12. Nondestructive Testing and Nondestructive Inspection
Visual Inspection
Borescope Inspection
Liquid Penetrant (Dye Penetrant) Inspection
Magnetic Particle Inspection
Radiographic Inspection (X-Rays and Gamma Rays)
Ultrasonic Inspection
Eddy Current Inspection
Review Problems
Endnotes
Chapter 13. Aviation Maintenance Management
Aviation Maintenance
Typical Airline Definition of Maintenance
Goals of a Maintenance Program
Functional and Potential Failure
Documentation for Maintenance
Requirements for a Maintenance Program
Material Support—Stores and Logistics
Material Department—Budgeting Efforts
Oversight Functions
Quality Assurance
Quality Control
Reliability
Summary
Review Problems
Endnotes
Chapter 14. Case Studies and Human Factors
Case Study 14-1 TWA Flight
Case Study 14-2 Atlantic Southeast Airlines Flight
Case Study 14-3 United Airlines Flight
Case Study 14-4 American Airlines Flight
Case Study 14-5 USAir Flight
Human Factors
Human Factors in Aircraft Maintenance
Maintenance Error Decision Aid
Review Problems
Endnotes
Answers to Chapter Questions
Index